任何物品都有自己的使用壽命或者缺陷，熒光燈也不例外，今天一起裝修網小編為大家帶來的就是熒光燈容易出現的問題以及其解決辦法，相信看完之后能夠對大家有一定的幫助。

故障原因:1.鎮流器損壞;2.燈管漏氣

排除方法:1.檢查電路接線，看鎮流器是否與燈管燈絲串聯在電路中，否則會因電流過大而燒毀燈絲。如接線正確，再用萬用表檢查鎮流器是否短路，如短路，說明鎮流器已失去限流作用，無疑要燒毀燈絲，應更換或修復后再使用。2.若鎮流器末短路，通電后燈管立即冒白煙，隨即燈絲燒毀，說明燈管嚴重漏氣，應更換新的燈管。

故障原因:1.燈管漏氣(針對電感鎮流器和常見的普通電子鎮流器);2.啟輝器損壞(針對電感式鎮流器);3.諧振電容擊穿(針對常見的普通電子鎮流器);4.燈絲燒斷(針對電感鎮流器)。

排除方法:1.電感鎮流器，若出現燈管兩端存在閃爍的橙紅色光，則說明燈管嚴重老化或者漏氣，可以嘗試更換燈管;如果是電子鎮流器若兩端燈絲持續而穩定的發出橙紅色光，沒有閃爍現象，則有可能是燈管漏氣，但也不排除是鎮流器諧振電容擊穿。可以嘗試更換燈管。2.燈管兩端出現穩定的沒有閃爍的橙紅色光，并且通電情況下拆下啟輝器，燈管可以正常點亮，這說明啟輝器存在短路性故障(大多是啟輝器內雙金屬片粘連，或啟輝器內部電容擊穿)，更換啟輝器即可。3.這種故障在維修中非常常見，電子鎮流器出現燈絲發紅但燈管不啟動現象大多是這種情況，可以嘗試更換鎮流器。諧振電容只有幾毛錢，應該首先嘗試更換這個電容修復鎮流器，不要因為這個幾毛錢的小元件而扔掉了整個鎮流器，太浪費了。4.一端發光，另一端不發光，有可能是發光的這一端的燈絲已經燒斷了，此時的發光并不是燈絲在發光，而是燈絲斷裂處的氣體被擊穿從而發光，此時電流很小因此另一端燈絲可能不發光。這種情況需要更換燈管。

熒光燈容易出現的故障以及解決辦法

故障原因:1.燈管質量問題，鎮流器工作電流過大。

排除方法:1.新燈管接入電路后，剛點燃即出現打滾現象，說明燈管內氣體不純以及燈管在出廠前老化不夠。遇到這種情況，只要反復啟動幾次即可使燈管進入正常工作狀態。如新燈管點燃數小時后才出現打滾現象。反復啟動也不能消除時，屬燈管質量問題，應更換燈管。若換上新燈管后仍出現打滾現象，則應用交流電流表串入鎮流器回路，檢查鎮流器能否起到限流作用，如發現電流過大，就應列換新的鎮流器或修復后再使用。

故障原因:1.開關接線錯誤;2.余輝現象。

排除方法:1.首先檢查熒光燈線路，看開關是否錯接在中性線上，若接在中性線上，由于燈管與墻壁間有電容存在，會使燈管斷電時仍有微光，當用手觸摸燈管時，輝光可能增強。這種情況，只要將開關改接在相線上就可消除輝光現象。如果改接后仍有輝光現象，則應檢查開關是否漏電。如發現開關漏電，一定要修復或換新，否則會嚴重影響燈管的使用壽命。2.如果接線無誤，但關閉電源后燈管依然發出微弱的光，并且數分鐘后自動消失，這就是燈管的余輝現象。余輝現象是正常現象，無需多慮。

故障原因:1.燈管老化;1.熒光燈附件不配套;3.開、關次數過于頻繁。

排除方法:1.當燈管點燃時間已接近或超過規定使用壽命，燈管兩端發黑是正常的，說明燈絲所涂復的電了發射物質即將耗盡。發黑部位一般在離燈管兩端約50 60mm范圍內。此時燈管雖然依然可以發光，發光強度也低于正常亮度了，應該考慮更換燈管。2.如新燈管使用不久兩端嚴重發黑，是由于燈絲上電子發射物質飛濺得太快，吸附在管壁上的緣故，可能是燈管質量不好，也有可能是鎮流器有問題導致燈絲電流太大。3.熒光燈開關的次數過于頻繁，熒光燈的啟動電流很大，開關次數過于頻繁會加快燈管老化。

故障原因:1.鎮流器鋼片松動(針對電感鎮流器);2.鎮流器過載;3.鎮流器故障前兆(針對電子鎮流器)

排除方法:1.鎮流器是一個帶鐵芯的低頻扼(e)流圈，通交流電時，由于電磁振動發出蜂音是正常的，但根據出廠標準，距離鎮流器lm處聽不到這種噪音為合格產品，當噪音超標時應更換新的鎮流器。安裝位置不當或松動會引起與周圍物體共振發出蜂音，只要在鎮流器下墊一塊橡膠材料緊固后即可解決。也可以嘗試瀝青、樹脂封固。2.燈管與鎮流器不匹配，或電源電壓過高，都會導致鎮流器過載從而發出比平時大的聲音，請檢查燈管與鎮流器是否匹配，以及電源電壓是否正常。3.電子鎮流器突然出現異常的吱吱聲，表明內部振蕩電路工作不正常，需要斷電檢查內部濾波電容是否失效，電阻、電容是否變質，以及電源電壓是否正常。比較常見的是電解電容失容。出現這種情況，可以嘗試更換鎮流器解決。

故障原因:1.鎮流器本身質量有問題;2.電源電壓過高

排除方法:先用交流電流表檢查電路中的電流即鎮流器的工作電流，如因鎮流器短路而造成工作電流過大時，應列換新的鎮流器或修復后再使用。若鎮流器通過電流符合標準范圍，電源電也不高，則應檢查啟輝器內電容器是否被擊穿，氖泡內部電極是否搭連。

以上是關于熒光燈的相關介紹，如果想要了解更多關于熒光燈的相關信息，請多多關注一起裝修網，一起裝修網將給大家提供更全、更詳細、更新的資訊信息。想了解更多關于熒光燈的信息，請關注一起裝修網每周末的建材家具團購會，價格將低于市場30%-50%，了解更多信息請搜索進入一起裝修網。